Things That Get Hot in the Studio

Feb 1, 2005 12:00 PM, By Eddie Ciletti

WHAT ARE METER BULBS AND CAPPUCCINOS?

Polls


Mix Regional

The Mix Regional section for Mix's July 2014 issue focuses on Atlanta. Send us your studio news: updates, sessions, new rooms, club performances and installations. Let the Mix audience know what is going on! Send photos and descriptions to mixeditorial@nbmedia.com.

Figure 1: A simple meter lamp dimmer circuit

In the past two issues, I wrote about vacuum tubes. This month, the filament-related theme continues. Light bulbs have been getting the nudge from LEDs for years, yet there are still plenty of old-fashioned VU meters to keep lit. In one month, I've encountered several meter lamp — challenged consoles — only one meter out of dozens remains lit.

I am often asked whether it's better to leave equipment powered 24/7 or turn it off. I believe professional gear should tolerate being “power-cycled,” especially if it is not in use every day. Heat dries out capacitors and wastes energy. Either way, bulb life is an issue, especially when replacement requires more than a little wrist action.

Whether for outboard gear, consoles or recorders, finding the right bulbs can be a chore. Sometimes the replacement procedure adds salt to the wound, especially when the bulbs must be soldered — or worse, they're soldered inside the meter.

Many popular bulbs in vintage '70s-era American-made gear use variations on the T1-3/4 “midget” series (bi-pin, screw, flange, groove and wedge). LEDtronics has LED alternatives that draw about half the current of a conventional incandescent bulb and last at least 10,000 hours. (One 24/7 year is 8,760 hours!) The catch is that some distributors require a sizable minimum order. However, according to an LEDtronics representative, its LED replacement for the common 7387 bulb is $6 each in quantities of one to nine. Not bad for a 2-track bus, but pricey if you're doing 24 (or 48!) VU lamps.

Figure 2: An SSL console meter with clear protective cover removed to access the lamps. At right, the incorrect Type 7387 bulb is installed (for comparison purposes); at left is an LED replacement.

SWAMP LITES
Many years ago, working in a poor studio somewhere in Jersey, I installed meter light dimmers on a 3M tape machine. By going easy on the juice, we got a lot more mileage out of those 48 bulbs; their only remaining punishment was to endure fast-wind shock therapy every three minutes or so! During a more recent Trident rackmount compressor upgrade, the bulbs and mounting hardware were completely missing. Using what was handy, I installed a very simple dimmer circuit, seen in Fig. 1.

Type 7387 is similar to what MCI used in its meters and costs just $0.65 each in 100-piece quantities. This version is rated at 28 volts, 40 mA, so it's conservatively “burning” when fed by a standard 24V supply. The lamps were adjusted to burn only as bright as necessary. Creative variations for this type of mod include adding a photo-resistor so the circuit self-adjusts for ambient light using a timer. If the meter lamps had a dedicated power supply, then it could be trimmed (or modified) down a few volts.

Bulb access for the Trident 65 meters requires removing the clear front cover. You'll need a soldering iron to get them out. Talk about fear factor! Just try to find the perfect bulb: one that's the same brightness and physical size as the others. Somewhat easier are the Soundcraft TS-12 lamps that are soldered to a PCB located behind the meter. These “grain of wheat” — style replacements (12V @ 50 mA) are available from www.mcminone.com as part #25-1370 — unbeatable at $0.26 each in small quantities.

By contrast, just about everything about SSL's 4000 Series was designed for service. It's possible to shut down individual eight-module “buckets” while leaving the rest of the console functional. The bi-pin — style bulbs are socketed inside the meter. Figure 2 shows a standard incandescent and an LED replacement; the latter gets surprisingly hot without a filament!

SCORCHED TASTE BUDS
Last on our theme of “stuff that gets hot” is advice for assistant engineers: Use a candy thermometer when steaming milk for my lattes and cappuccinos! Boiling water is 212° F (100° C), but steam under pressure can be considerably higher. Either way, 140° F is all it takes.


Eddie welcomes all to latte-practice. Be sure to bring your fave LPs and 45s. Visit www.tangible-technology.com if ya can't travel.






Acceptable Use Policy
blog comments powered by Disqus

Mix Books

Modern Recording and Mixing

This 2-DVD set will show you how the best in the music industry set up a studio to make world-class records. Regardless of what gear you are using, the information you'll find here will allow you to take advantage of decades of expert knowledge. Order now $39.95

Mastering Cubase 4

Electronic Musician magazine and Thomson Course Technology PTR have joined forces again to create the second volume in their Personal Studio Series, Mastering Steinberg's Cubase(tm). Edited and produced by the staff of Electronic Musician, this special issue is not only a must-read for users of Cubase(tm) software, but it also delivers essential information for anyone recording/producing music in a personal-studio. Order now $12.95

Newsletters

MixLine

Delivered straight to your inbox every other week, MixLine takes you straight into the studio, with new product announcements, industry news, upcoming events, recent recording/post projects and much more. Click here to read the latest edition; sign up here.

MixLine Live

Delivered straight to your inbox every other week, MixLine Live takes you on the road with today's hottest tours, new sound reinforcement professional products, recent installs, industry news and much more. Click here to read the latest edition; sign up here.

[an error occurred while processing this directive]

The Wire, a virtual press conference offering postings of the latest gear and music news, direct from the source. Visit the The Wire for the latest press postings.